Table of Contents
Run Setup
The below setup is a change in wiring from Run 76, where we see 4 non-working phonon channels and were able to assign the issue to some particular SQUIDS. Since the same SQUET boards are re-used in this run, we will keep Side 2 fully working and Phonon Channel F and A from Side 1 working.
Non-working channels: link Cable 2 SQUID A, Cable 1 SQUID C&D, Cable 3 SQUID C
| Run 78 Channel Map | |||||||
|---|---|---|---|---|---|---|---|
| Prev Det TwistedPair Conn refer | New Det TwistedPair Conn | Tower | Cable | DCRC(2sided) | Label | SQUID Bias, Offset | HV output, Side2-readout |
| DIB1Q (Side1pE) | DIB1Q (Side1pE) | Face5pA | Cable 2 (includes LEDs and accessories) HV CONN1 Stripline 41 ZC-70 | DCRC1 | - | ||
| DIB1pB (Side1pB) | DIB3pA (Side1pF) | Face5pB | SQUID Bias= -71.8 uA, Lockpoint=-2.94 mV, | - | |||
| DIB1pA (Side1pD) | DIB4pC (Side1pA) | Face5pC | SQUID Bias= -81.1 uA, Lockpoint=-4.77 mV | - | |||
| DIB1pC (Side2pE) | DIB1pC (Side2pE) | Face5pD | SQUID Bias= -88.5 uA, Lockpoint=-2.78 mV | - | |||
| DIB3pC (Side2pC) | DIB3pC (Side2pC) | Face3pA | Cable 1 HV CONN2 | DCRC3 | SQUID Bias= -58.1 uA, Lockpoint=-3.44 mV | - | |
| DIB3pB (Side2pF) | DIB3pB (Side2pF) | Face3pB | SQUID Bias= -80.1 uA, Lockpoint=-3.95 mV | - | |||
| DIB3Q (Side1pC) | DIB3Q (Side1pC) | Face3pC | - | - | |||
| DIB3pA (Side1pF) | DIB1pA (Side1pD) | Face3pD | - | - | |||
| DIB3pD (Side2pB) | DIB3pD (Side2pB) | Face2pA | Cable 3 HV CONN3 | DCRC4 | SQUID Bias= -89.0 uA, Lockpoint=-5.42 mV | - | |
| DIB4pD (Side2pA) | DIB4pD (Side2pA) | Face2pB | SQUID Bias= -85.9 uA, Lockpoint=-4.13 mV | - | |||
| DIB4pC (Side1pA) | DIB1pB (Side1pB) | Face2pC | - | - | |||
| DIB1pD (Side2pD) | DIB1pD (Side2pD) | Face2pD | SQUID Bias= -88.2 uA, Lockpoint=-3.32 mV | - | |||
Accessory wiring
The idea is to do minimal change to the setup from Run 77 so that 2D source mover can be swapped without any wire mapping change. So, the ideal place to make change is at the connection from the 1D source mover housing. The two coils are currently wrapped as a set of 4 pins which can be broken into half. Similarly, the far and near endstop can be made into individual wires to plug into the Tower face.
(Old) Refer page: Link to Run 72 wiring
(Old) Refer to 1D source mover notes.Link
| Run 78 accessory wiring | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| accessory | Motor Y1 | Motor Y2 | Motor Y3 | Motor Y4 | Motor X1 | Motor X2 | Motor X3 | Motor X4 | Xendstop | Yendstop | ||||||
| acc wire | SL Yconnector | SL ROX connector | purple | purple | ||||||||||||
| Tower F4 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
| interposer conns | brn | w brn | org | w org | blu | w blu | grn | blk | blk | pur | pur | |||||
| no soc | no soc | no soc | no soc | no soc | no soc | no soc | no soc | no soc | ||||||||
| stripline pin | 49 | 50 | 8 | 9 | 11 | 12 | 13 (open) | 45 | 2 | 46 | ||||||
| label | pBr3 | pBr4 | pCr3 | pCr4 | pAr3 | pAr4 | pAr5 | pDr3 | pAr1 | pDr4 | ||||||
| STRIPLINE 41 | ||||||||||||||||
| CABLE #2 | ||||||||||||||||
| stripline D50 | 36 | 18 | 8 | 23 | 4 | 19 | 1 | 41 | 17 | 40 | ||||||
| DCRC/diverter Dsub | 48 | 33 | 10 | 28 | 14 | 32 | 17 | 43 | 1 | 44 | ||||||
| Dsub diverter board | U09-2 | U10-3 | U06-3 | U07-3 | U08-4 | U09-1 | U10-4 | U06-4 | U01-4 | U07-5 | ||||||
| Run75 Warm-side Accessory Wires: Motor coil (MC), endstop (ES), Goldman thermometer (GT) | ||||||||||||||||
| diverter board wires | MC Orange | MC Brown | MC Red | MC Yellow | GT Black | ES White Blue | ES Green | GT White | GT Red | GT Green | ? | |||||
SQUID Status
| Run 78 Channel Map | ||||||
|---|---|---|---|---|---|---|
| New Det TwistedPair Conn | Tower | Cable | DCRC(2sided) | Label | HV output, Side1-readout | HV output, Side2-readout |
| DIB1Q (Side1pE) | Face5pA | Cable 2 (includes LEDs and accessories) HV CONN1 | DCRC1 | HV1 pA | - | |
| DIB3pA (Side1pF) | Face5pB | HV1 pB | - | |||
| DIB4pC (Side1pA) | Face5pC | HV1 pC | - | |||
| DIB1pC (Side2pE) | Face5pD | - | HV2 pD | |||
| DIB3pC (Side2pC) | Face3pA | Cable 1 HV CONN2 | DCRC3 | - | HV2 pA | |
| DIB3pB (Side2pF) | Face3pB | - | HV2 pB | |||
| DIB3Q (Side1pC) | Face3pC | HV2 pC | - | |||
| DIB1pA (Side1pD) | Face3pD | HV2 pD | - | |||
| DIB3pD (Side2pB) | Face2pA | Cable 3 HV CONN3 | DCRC4 | - | HV1 pA | |
| DIB4pD (Side2pA) | Face2pB | - | HV1 pB | |||
| DIB1pB (Side1pB) | Face2pC | HV2 pB | - | |||
| DIB1pD (Side2pD) | Face2pD | - | HV1 pD | |||